Skip to content
Tankless Costs Guide

Tankless Water Heater Installation Cost (2026 Price Guide)

Updated November 2026

Short answer: installing a tankless water heater typically costs $1,200 – $3,500 in 2026 (This Old House). Electric jobs often land at $650 – $2,500, and gas jobs at $1,650 – $3,500. Gas line, venting and electrical upgrades are what push a job to the top of the range.

Tankless Water Heater Cost Calculator

Sets the unit size: roughly 2-4 GPM for 1-2 people, 5-7 GPM for 3-4, 8-10 GPM for 5 or more.

Typical when moving from an electric or tank heater to gas tankless.

Gas tankless units need sealed stainless or PVC venting, often different from a tank heater's flue.

Sets local labor rates.

Your estimated cost

$1,800 – $4,200

Typical: $3,000

Using national average prices. Add your zip code for local prices.

  • Tankless unit$750 – $2,000
  • Installation labor and fittings$900 – $1,500
  • Removal of old heater$100 – $500
  • Permit$50 – $200
  • Ask whether the quote includes the permit, any required inspection and removal of the old unit.
  • Gas tankless heaters usually need a larger gas line and new venting. Have the installer check your gas meter and line size before you sign.
  • Hard water shortens a tankless heater's life. If your water is hard, ask about a softener or a scheduled descaling service.

Plumber fitting the water connections on a newly installed tankless water heater

Installed cost by fuel type

TypeUnitLabor and fittingsTotal installed
Natural gas$750 – $2,000$900 – $1,500$1,650 – $3,500
Electric, whole-house$500 – $1,500$150 – $1,000$650 – $2,500
PropaneUsually priced like gas, with a higher unit cost in some models$1,400 – $3,500
Sources: This Old House, updated June 2026; HomeGuide, 2026. HomeGuide’s wider range is $1,400 – $5,600 for tankless overall.

Extras that change the price

ExtraTypical cost
Larger or new gas line$350 – $750
New venting$400 – $800
New electrical circuit$200 – $600
Electrical panel upgrade$1,000 – $2,000
Removing the old heater$100 – $500
Permit$50 – $200
Sources: This Old House; Angi; HomeGuide, 2026.

What the installation price covers

Installation takes about 4 to 8 hours. The labor and fittings line pays for the work below. Anything your home lacks, such as a big enough gas line, is priced as an extra on top.

StepWhat the installer doesGasElectric
SurveyChecks gas line and meter, or panel capacity, and picks the mounting spotYesYes
Remove the old heaterDrains, disconnects and takes it away (often a separate line)YesYes
Mount the unitFixes the heater to the wall and connects hot and cold water with isolation valvesYesYes
Gas connectionConnects, and upsizes if needed, the gas supplyYesNo
VentingRuns sealed venting through a wall or the roofYes, unless outdoorNo
Condensate drainPipes away the water a condensing unit producesCondensing unitsNo
ElectricalProvides a power outlet (gas) or dedicated 240-volt circuits (electric)MinorMajor
CommissioningTests for leaks, sets the temperature and checks flowYesYes
General description of a typical install. Your installer’s scope may differ, so ask for it in writing.

Installation cost by scenario

ScenarioExtras countedEstimated total, 3 to 4 person home
Replace a gas tankless unit with a similar onePermit$1,700 – $3,700
Replace an electric tankless unit with a similar onePermit$700 – $2,700
Gas tank to gas tanklessGas line, venting, tank removal, permit$2,550 – $5,750
Electric tank to electric tankless, panel has capacityNew circuit, tank removal, permit$1,000 – $3,800
Electric tank to electric tankless, panel is fullNew circuit, panel upgrade, tank removal, permit$2,000 – $5,800
Point-of-use electric unit at one sinkNew circuit, permit$500 – $1,600
Our arithmetic from the ranges in the two tables above. Point-of-use labor ($100 – $300) is our own working assumption. National averages before local labor rates.

Permits and inspections

Most areas require a permit to install or replace a water heater, typically $50 to $200. Some need separate plumbing and electrical permits, and a safety inspection where required adds about $74 to $150. A licensed installer normally pulls the permit and books the inspection. Check that both are in the quote, because unpermitted work can cause problems when you sell the home or make an insurance claim.

Professional or DIY installation?

A small point-of-use electric unit is the only tankless job that is commonly done by a confident homeowner, and even then the circuit work is for an electrician. Whole-house units involve gas piping, combustion venting or high-amperage wiring, which most areas restrict to licensed trades. Makers can also make professional installation a warranty condition. This is general guidance: check your local code and the warranty for your model.

What drives your price

  • Fuel and swap type. Replacing an existing tankless unit is cheapest; switching from a tank costs more. See the cost to replace a tank with tankless.
  • Size. Larger households need more flow. See our sizing guide.
  • Brand and efficiency. Condensing models cost more. Compare Rinnai, Navien and others.
  • Where you live. Local labor rates vary, which is why the calculator asks for your ZIP code.

Tax credit: the federal credit for tankless heaters ended for equipment installed after December 31, 2025. Check your utility and state for rebates.

Go deeper: gas tankless costs, electric tankless costs and our buying guide.

Installation cost FAQs

How much is labor alone to install a tankless water heater?

This Old House puts labor and fittings at $900 to $1,500 for gas and $150 to $1,000 for electric. At a plumber’s rate of $75 to $150 an hour, a 4 to 8 hour job is $300 to $1,200 in time alone, before fittings, valves and any second trade.

Why does a gas install cost more than an electric one?

A gas heater needs a gas supply big enough for its burner, sealed venting to the outside and, for condensing models, a condensate drain. An electric heater needs none of those. Its cost risk is the wiring: a new circuit, or a panel upgrade for a whole-house unit.

Does the installation price include removing my old heater?

Not always. Removal and disposal is commonly a separate line of $100 to $500, and Angi reports $500 or more in some cases. Ask for it to be written into the quote.

Can I buy the heater myself and pay only for installation?

Some installers will fit a heater you supply and some will not. Ask before you buy, and ask what it does to their labor warranty. Check the maker’s warranty terms too, because several require installation by a licensed professional.

How long does installation take?

About 4 to 8 hours for a typical job. Gas line, venting or panel work can stretch it to a second day, and an inspection may be needed before sign-off.