Short answer: installing a tankless water heater typically costs $1,200 – $3,500 in 2026 (This Old House). Electric jobs often land at $650 – $2,500, and gas jobs at $1,650 – $3,500. Gas line, venting and electrical upgrades are what push a job to the top of the range.
Tankless Water Heater Cost Calculator
Your estimated cost
$1,800 – $4,200
Typical: $3,000
Using national average prices. Add your zip code for local prices.
- Tankless unit$750 – $2,000
- Installation labor and fittings$900 – $1,500
- Removal of old heater$100 – $500
- Permit$50 – $200
- Ask whether the quote includes the permit, any required inspection and removal of the old unit.
- Gas tankless heaters usually need a larger gas line and new venting. Have the installer check your gas meter and line size before you sign.
- Hard water shortens a tankless heater's life. If your water is hard, ask about a softener or a scheduled descaling service.
Sorry, we couldn't calculate that. Please check your answers, or reload the page.
Compare quotes from local tankless installers
Free, with no obligation. Local, pre-screened pros will contact you to confirm your project and give you a price.
Thanks! Your request is on its way. Local pros will contact you shortly, usually within a business day, to talk about your project.
Check your quote
We compare it with the estimate for your answers above and your zip code.
Estimates are a guide. Prices vary with your home and local conditions.
Questions to ask
Red flags

Installed cost by fuel type
| Type | Unit | Labor and fittings | Total installed |
|---|---|---|---|
| Natural gas | $750 – $2,000 | $900 – $1,500 | $1,650 – $3,500 |
| Electric, whole-house | $500 – $1,500 | $150 – $1,000 | $650 – $2,500 |
| Propane | Usually priced like gas, with a higher unit cost in some models | $1,400 – $3,500 | |
Extras that change the price
| Extra | Typical cost |
|---|---|
| Larger or new gas line | $350 – $750 |
| New venting | $400 – $800 |
| New electrical circuit | $200 – $600 |
| Electrical panel upgrade | $1,000 – $2,000 |
| Removing the old heater | $100 – $500 |
| Permit | $50 – $200 |
What the installation price covers
Installation takes about 4 to 8 hours. The labor and fittings line pays for the work below. Anything your home lacks, such as a big enough gas line, is priced as an extra on top.
| Step | What the installer does | Gas | Electric |
|---|---|---|---|
| Survey | Checks gas line and meter, or panel capacity, and picks the mounting spot | Yes | Yes |
| Remove the old heater | Drains, disconnects and takes it away (often a separate line) | Yes | Yes |
| Mount the unit | Fixes the heater to the wall and connects hot and cold water with isolation valves | Yes | Yes |
| Gas connection | Connects, and upsizes if needed, the gas supply | Yes | No |
| Venting | Runs sealed venting through a wall or the roof | Yes, unless outdoor | No |
| Condensate drain | Pipes away the water a condensing unit produces | Condensing units | No |
| Electrical | Provides a power outlet (gas) or dedicated 240-volt circuits (electric) | Minor | Major |
| Commissioning | Tests for leaks, sets the temperature and checks flow | Yes | Yes |
Installation cost by scenario
| Scenario | Extras counted | Estimated total, 3 to 4 person home |
|---|---|---|
| Replace a gas tankless unit with a similar one | Permit | $1,700 – $3,700 |
| Replace an electric tankless unit with a similar one | Permit | $700 – $2,700 |
| Gas tank to gas tankless | Gas line, venting, tank removal, permit | $2,550 – $5,750 |
| Electric tank to electric tankless, panel has capacity | New circuit, tank removal, permit | $1,000 – $3,800 |
| Electric tank to electric tankless, panel is full | New circuit, panel upgrade, tank removal, permit | $2,000 – $5,800 |
| Point-of-use electric unit at one sink | New circuit, permit | $500 – $1,600 |
Permits and inspections
Most areas require a permit to install or replace a water heater, typically $50 to $200. Some need separate plumbing and electrical permits, and a safety inspection where required adds about $74 to $150. A licensed installer normally pulls the permit and books the inspection. Check that both are in the quote, because unpermitted work can cause problems when you sell the home or make an insurance claim.
Professional or DIY installation?
A small point-of-use electric unit is the only tankless job that is commonly done by a confident homeowner, and even then the circuit work is for an electrician. Whole-house units involve gas piping, combustion venting or high-amperage wiring, which most areas restrict to licensed trades. Makers can also make professional installation a warranty condition. This is general guidance: check your local code and the warranty for your model.
What drives your price
- Fuel and swap type. Replacing an existing tankless unit is cheapest; switching from a tank costs more. See the cost to replace a tank with tankless.
- Size. Larger households need more flow. See our sizing guide.
- Brand and efficiency. Condensing models cost more. Compare Rinnai, Navien and others.
- Where you live. Local labor rates vary, which is why the calculator asks for your ZIP code.
Tax credit: the federal credit for tankless heaters ended for equipment installed after December 31, 2025. Check your utility and state for rebates.
Go deeper: gas tankless costs, electric tankless costs and our buying guide.
Installation cost FAQs
How much is labor alone to install a tankless water heater?
This Old House puts labor and fittings at $900 to $1,500 for gas and $150 to $1,000 for electric. At a plumber’s rate of $75 to $150 an hour, a 4 to 8 hour job is $300 to $1,200 in time alone, before fittings, valves and any second trade.
Why does a gas install cost more than an electric one?
A gas heater needs a gas supply big enough for its burner, sealed venting to the outside and, for condensing models, a condensate drain. An electric heater needs none of those. Its cost risk is the wiring: a new circuit, or a panel upgrade for a whole-house unit.
Does the installation price include removing my old heater?
Not always. Removal and disposal is commonly a separate line of $100 to $500, and Angi reports $500 or more in some cases. Ask for it to be written into the quote.
Can I buy the heater myself and pay only for installation?
Some installers will fit a heater you supply and some will not. Ask before you buy, and ask what it does to their labor warranty. Check the maker’s warranty terms too, because several require installation by a licensed professional.
How long does installation take?
About 4 to 8 hours for a typical job. Gas line, venting or panel work can stretch it to a second day, and an inspection may be needed before sign-off.
Sources: This Old House; HomeGuide; Angi. Prices last checked November 2026. How we make money. Related: repair costs, propane costs, point-of-use costs, is tankless worth it, compare models, all guides.